Fox DHX2 Factory Shock - 210x50 - Standard: Metric

Fox DHX2 Factory 2026 is a coil shock designed for demanding gravity riding, downhill and enduro. The model uses a completely new construction based on Monotube technology, offering high sensitivity, predictable damping and a wide range of adjustments. Thanks to the pressure balancing system, increased shaft diameter and four independent adjustments, Fox DHX2 provides riders with control, traction and confidence in very demanding terrain.

Features

• Intended use: downhill, enduro, gravity riding
• Monotube technology: new damping construction increasing control and reliability
• Pressure balancing: supports sensitivity on small bumps and damping control under high load
• 4 adjustments: independent low-speed and high-speed compression adjustment, as well as low-speed and high-speed rebound adjustment
• Increased shaft diameter: 12.7 mm for greater strength and durability
• Sensitivity and traction: construction designed for precision and riding confidence at high speeds

Note: the spring is not included in the set. It must be selected and purchased separately according to the rider's weight, bike and preferred suspension setup.

• Model: Fox DHX2
• Series: Factory
• Model year: 2026
• Type: coil shock
• Mount: standard
• Standard: Metric
• Size: 210x50 mm
• Eye-to-eye length: 210 mm
• Stroke: 50 mm with the option to increase to 55 mm
• Adjustments: Hsc, Lsc, Hsr, Lsr and 2Pos lever
• Damper control: 2Pos-Adj
• Starting weight: 568 g without spring for size 210x55 with 2Pos lever
• Part number: 978-01-604

Adjustments

• HSC: high-speed compression adjustment
• LSC: low-speed compression adjustment
• HSR: high-speed rebound adjustment
• LSR: low-speed rebound adjustment
• 2pos-Adj: two-position lever

Sizes

• Shock size: 210x50 mm
• Eye-to-eye length: 210 mm
• Stroke: 50 mm
• Option to increase stroke: up to 55 mm

Included in the set

• Tool: for compression adjustment
• Sticker: Fox
• Manual: Owner's Manual / Tuning Guide

Note: the spring is not included in the set. It must be selected and purchased separately according to the rider's weight, bike and preferred suspension setup.

Service intervals, zero service and practical tips.

We recommend watching our video and taking a few minutes to read the article about service intervals to understand how to take care of your suspension:

Link to the article

Link to the YouTube video

    Service intervals recommended by Fox

 

Regularly Before and after riding	25	125	200	300
	hours	hours / 1 year	hours / 1 year	hours / 1 year
	Basic seatpost service	Intermediate seatpost service	Full seatpost service	Full seatpost service
Check the sag and suspension settings. Check the controls for visible damage and proper operation	Transfer 2025-2026 Transfer Neo (25 h or every 1000 actuations - information in the Fox Bike app)	Transfer 2025-2026	Transfer Neo (200 h or every 8000 actuations - information in the Fox Bike app)	Transfer 2025-2026
		Full seatpost service
Check that quick-release levers and axles are properly adjusted and tightened		Transfer 2021-2024 Transfer 2017-2020 Transfer Sl 2022-2026
		Full fork service
Clean the outside of the suspension components only with mild soap and water, then wipe dry with a soft towel. Do not use a pressure washer or spray water directly onto the seal-to-suspension connection Check the entire outside of the fork/shock. Do not use the fork/shock if any of its external components appear to be damaged		Fox 32 Fox 34 Fox 36 Fox 38 Fox 40 Fox Podium Fox Dps Fox Dpx Fox Float X Fox Float X2 Fox Dhx Fox Dhx2 Fox Van Fox Float Sl Fox Float X/Dhx Live Valve Neo Fox Awl

For riders using DH, Park or Extreme Freeride bikes with lift access, or riding in extremely wet/muddy or dry/dusty conditions where trail debris gets onto the fork or shock, Fox encourages earlier maintenance than recommended above, if needed. If you hear, see or feel anything unusual, stop riding immediately and contact an authorized Fox service center for the appropriate inspection.




We recommend!
We recommend performing a small service of Fox forks every 50 hours of use, especially in models equipped with Grip dampers.
In this type of construction, oil circulates between the damper and the lower legs, which means that any contamination entering the lower legs can also get into the damper.
Please remember that the 125/200/300 h intervals are interchangeable with a period of 1 year - if the equipment does not reach the hourly interval within one year, the service should be performed before the end of 1 year.
Especially important during the warranty period.
 

Manufacturer:
Fox Factory Inc.
2055 Sugarloaf Circle
Suite 300 30097 Duluth
Georgia
United States

Person responsible in the EU:
FOX FACTORY GmbH
Gewerbepark 6
66989 Höhfröschen
Germany
https://www.foxracingshox.de/