Fox DHX2 Factory Shock - 205x60 - Standard: Metric Trunnion

A coil gravity shock designed for downhill and enduro riding. The model was developed for racers and riders who expect maximum traction, control and predictable suspension performance at high speeds and in demanding terrain. The new construction based on Monotube technology increases durability and reliability while maintaining a wide range of four independent adjustments.

• Intended use: downhill, enduro, racing DH, gravity riding
• Monotube construction: increases shock durability and reliability
• Coil spring performance: provides high sensitivity, traction and control in difficult terrain
• Identical internal construction to the Float X2 model: supports damping consistency and a wide adjustment range
• Pressure balancing: improves sensitivity over small bumps and damping control under heavy load
• Four independent adjustments: low and high speed compression, plus low and high speed rebound
• 2pos-Adj lever: allows the shock’s operating mode to be changed
• Increased shaft diameter: 12.7 mm for greater strength and durability

• Model: Fox DHX2
• Series: Factory
• Model year: 2026
• Mount: Metric Trunnion
• Eye-to-eye length: 205 mm
• Stroke: 60 mm with the option to increase to 65 mm
• Starting weight: 568 g without spring for size 210x55 with 2pos lever
• Part number: 978-01-610

Adjustments

• HSC: high speed compression adjustment
• LSC: low speed compression adjustment
• HSR: high speed rebound adjustment
• LSR: low speed rebound adjustment
• 2pos-Adj: two-position lever

Sizes

• Shock size: 205x60 mm
• Eye-to-eye length: 205 mm
• Stroke: 60 mm
• Option to increase stroke: up to 65 mm

What’s in the box

• Compression adjustment tool
• Fox sticker
• Owner’s manual and tuning guide

Service intervals, initial service and practical tips.

We recommend watching our video and taking a few minutes to read the article about service intervals to understand how to take care of your suspension:

Link to the article

Link to the YouTube video

    Service intervals recommended by Fox

 

Regularly Before and after riding	25	125	200	300
	hours	hours / 1 year	hours / 1 year	hours / 1 year
	Basic seatpost service	Intermediate seatpost service	Full seatpost service	Full seatpost service
Check suspension sag and settings. Check the controls for visible damage and proper operation	Transfer 2025-2026 Transfer Neo (25 h or every 1000 actuations - info in the Fox Bike app)	Transfer 2025-2026	Transfer Neo (200 h or every 8000 actuations - info in the Fox Bike app)	Transfer 2025-2026
		Full seatpost service
Check that quick release levers and axles are properly adjusted and tightened		Transfer 2021-2024 Transfer 2017-2020 Transfer SL 2022-2026
		Full fork and shock service
Clean the exterior of the suspension components only with mild soap and water, then wipe dry with a soft towel. Do not use a pressure washer and do not spray water directly onto the connection between the seal and the suspension component Check the entire exterior of the fork/shock. Do not use the fork/shock if any of its external parts appear to be damaged		Fox 32 Fox 34 Fox 36 Fox 38 Fox 40 Fox Podium Fox DPS Fox DPX Fox Float X Fox Float X2 Fox DHX Fox DHX2 Fox VAN Fox Float SL Fox Float X/DHX Live Valve Neo Fox AWL

For riders using DH, park or extreme freeride bikes with lift access, or riding in extremely wet/muddy or dry/dusty conditions where trail debris gets onto the fork or shock, Fox recommends performing maintenance earlier than listed above, if needed. If you hear, see or feel anything unusual, stop riding immediately and contact an authorized Fox service center for the appropriate inspection.




We recommend!
We recommend performing a small service on Fox forks every 50 hours of use, especially on models equipped with Grip dampers.
In this type of construction, oil circulates between the damper and the lower legs, which means that any contaminants entering the lower legs may also get into the damper.
Please remember that the 125/200/300 h intervals are interchangeable with a period of 1 year - if the equipment does not reach the hourly interval within a year, the service should be performed before 1 year has passed.
This is especially important during the warranty period.
 

Manufacturer:
Fox Factory Inc.
2055 Sugarloaf Circle
Suite 300 30097 Duluth
Georgia
United States

Person responsible in the EU:
FOX FACTORY GmbH
Gewerbepark 6
66989 Höhfröschen
Germany
https://www.foxracingshox.de/